Tecnicon Engineering Private Limited

Tank Type: Vertical cylindrical storage tank

Installation: Aboveground or underground

Use: Water, chemicals, fuel, oil, food, pharma, etc.

Orientation: Vertical

Location: Indoor or outdoor

Total Volume: e.g., 1,000 to 100,000 liters

Working Volume: 90–95% of total

Dimensions: Height, diameter, wall thickness

Height-to-Diameter Ratio: As per design

Shell/Heads:

• Carbon Steel, SS304, SS316, 

Internal Lining: Epoxy, rubber, PTFE

External Finish: Painted, polished, cladded, insulated

Design Code: API 650, API 620, ASME Sec VIII, IS 803

Design Pressure: Atmospheric or pressurized (e.g., -0.1 to 3 bar)

Design Temperature: e.g., -20°C to +150°C

Corrosion Allowance: e.g., 1.5 mm

Wind/Seismic Design: Yes/No (based on site)

Bottom: Flat, sloped, dish, conical

Roof: Flat, cone, dome, open-top, floating

Drainage: Self-draining (for hygiene-critical uses)

Support Type: Skirt, legs, ring beam, flat bottom on RCC

Anchors: Yes/No

Load Design: Seismic/wind loads per site

Manhole/Handhole

Inlet/Outlet Nozzles

Vent/Overflow

Drain/Sampling Nozzles

Level Port

Thermowell

Spare Ports

Insulation Type: Mineral wool, PUF

Thickness: e.g., 50 mm

Cladding Material: SS, aluminum, GI

Internal Coating: Food-grade, epoxy, rubber

External Coating: Primer + topcoat (epoxy or PU)

Surface Prep: SA 2.5 / SP10 (per SSPC/NACE)

Level Sensor: Sight, radar, ultrasonic

Temperature Sensor: RTD / thermocouple

Pressure Sensor (if pressurized)

Alarms: High/Low level

Other: pH, conductivity (if needed)

Pressure/Vacuum Relief Valve

Emergency Vent / Manhole

Flame Arrestor (for flammables)

Overflow Protection

Bund Wall (if required)

Grounding Lugs

Drain Valve: Ball/butterfly/flush type

CIP/SIP: Clean/Steam-in-Place options

Spray Ball / Rotary Cleaner

Power Supply (for instruments/valves)

Steam/Hot Water/Chilled Water (if temperature controlled)

Compressed Air

Lighting (for large tanks)

For storing:

• Water (raw, DM, process)

• Chemicals (non-corrosive)

• Oils (lubricating, fuel, etc.)

• Effluent or utility fluids

Nominal Volume: 5 KL (5000 Liters)

Working Volume: ~4800–4900 Liters

Orientation: Vertical cylindrical with flat or dished bottom

Shell & Bottom/Top: Mild Steel (IS 2062 Grade A/B)

Top Head: Flat or conical (based on application)

Bottom Head: Flat or dished

Supports: MS legs or skirt support (based on height/diameter)

Internal Coating:

• Bare MS (for water or non-corrosive fluids)

• Optional epoxy, rubber, or FRP lining (for chemical compatibility)

External Finish:

• Red oxide primer + industrial enamel paint

• Optional epoxy topcoat for outdoor use

IS 803 (Indian Standard for MS storage tanks)

API 650 (optional, for large storage tanks)

Custom fabrication standards per client requirement

Design Pressure: Atmospheric (standard)

Design Temperature: Ambient to 100°C (depends on fluid)

Non-pressurized: Not designed to handle pressure or vacuum

Diameter: ~1500 mm to 1800 mm

Height: ~2500 mm to 3000 mm (excluding nozzles)

Shell Thickness: 5 mm to 8 mm (depending on design)

Bottom/Top Thickness: 6 mm to 10 mm

Inlet: 1.5” or 2” (flanged or threaded)

Outlet: 2” or 3” with butterfly or ball valve

Vent: 1” with mesh or flame arrestor (optional)

Drain: Bottom 1” or 1.5” with valve

Overflow: 1” (optional)

Manhole: 400–500 mm dia. with bolted cover (top or side)

Instrumentation Ports (optional):

• Level gauge nozzle

• Temperature thermowell

• Pressure gauge (if jacketed)

Vertical Legs: 3 or 4 MS angle/channel legs with base plates

Skirt Support: Optional for large or tall tanks

Anchor Bolts: Provided for foundation grouting

Ladder and cage (for maintenance access)

Top railing or platform (for manhole access)

Level indicators (float or glass tube type)

Sight glass with guard

Coating for weather or corrosion protection

FRP or epoxy lining (for chemical resistance)

Nameplate with tank ID and capacity

Industrial water storage (DM, raw, process)

Lube/fuel oil storage

ETP/STP water tank

Utility chemical storage

Buffer tank for batching/mixing plants

Type: Air Receiver Tank (Compressed Air Storage)

Orientation: Vertical / Horizontal

Application: Industrial / Commercial / Utility

Mounting: Skid / Leg-supported / Saddle base

Location: Indoor / Outdoor

Volume: e.g., 250 L, 500 L, 1000 L, 3000 L, etc.

Working Pressure: e.g., 8 bar / 10 bar / 16 bar

Design Pressure: Typically 1.3 × working pressure

Diameter & Height / Length

Wall Thickness

Shell & Heads: Carbon Steel / Stainless Steel

Internal Surface: Painted / Bare / Lined (optional)

External Surface: Epoxy primer + PU paint / Powder-coated

Corrosion Allowance: e.g., 1.5 mm

Design Code: ASME Section VIII Div 1 / IS 2825 / PED / CE

Test Pressure: 1.5 × Design Pressure

Temperature Range: e.g., -10°C to 100°C

Air Inlet

Air Outlet

Drain Valve (manual or auto)

Safety Valve Port

Pressure Gauge Port

Manhole / Inspection Opening (for large tanks)

Safety Relief Valve

Pressure Gauge

Drain Valve (ball / auto drain)

Air Filter / Moisture Trap (optional)

Level Indicator (if required)

Vertical Tank: Legs or skirt

Horizontal Tank: Saddle base

Foundation Bolts: Yes / No

Lifting Lugs: Yes / No

Internal: Anti-corrosive / Bare

External: Epoxy painted / Powder coated

Surface Prep: SA 2.5 (if painted)

Hydrotest: 1.5 × Design Pressure

Pneumatic Test: Optional

NDT (if required): Radiography / UT / MPI

Visual & Dimensional Check

Datasheet & GA Drawing

Material Test Certificates (MTC)

WPS / PQR / Welder Qualification

Test Reports: Hydro / NDT

Pressure Vessel Certification (if required)

User Manual / O&M Guide

Tank type: Vertical / Horizontal

Application: Water / Chemical / Oil / Pharma / Food-grade

Orientation: Vertical / Horizontal

Installation: Aboveground / Indoor / Outdoor

Total volume

Working volume

Height

Diameter

Wall thickness

Shell/head material: SS304 / SS316 / CS

Internal lining/coating: Epoxy / Rubber / PTFE / Food-grade

External finish: Painted / Polished / Cladded / Insulated

Design code: ASME / API / IS / ISO

Design pressure

Design temperature

Corrosion allowance

Wind/seismic design

Certification: GMP / FDA / CE / ATEX (if applicable)

Type: Tubular / Flat / Full-length window

Mounting: Welded / Flanged / Clamped

Glass material: Borosilicate / Acrylic / Toughened

Level range: Full or partial

Protection: Guard rods / Cage

Backlight/scale: Optional

Cleanability: Easy-clean / Sanitary design

Inlet nozzle

Outlet nozzle

Drain nozzle

Overflow nozzle

Vent/breather nozzle

Sampling port

Manhole / Handhole

Sight glass ports

Thermowell

Support type: Legs / Skirt / Saddle

Anchor bolts

Earthing lug

Sight glass (main level indicator)

Optional level sensor: Radar / Ultrasonic / Magnetic

Temperature sensor

Pressure gauge (if pressurized)

Level alarms: High / Low

Insulation type: Rock wool / PUF 

Thickness

Cladding material: SS / Aluminum / GI

Drain valve type

CIP/SIP system: Yes/No

Spray ball / Rotary cleaner

Sanitary fittings: Tri-clamp / DIN / SMS

Pressure/vacuum relief valve

Emergency vent

Flame arrestor (if required)

Overflow protection

Bund wall (if required)

Sight glass protection

Electrical supply

Compressed air

Steam / Hot water / Chilled water

Gauge lighting (optional)

Material Test Certificates (MTC)

Welding docs: WPS / PQR / Welder certificates

Hydrotest report

NDT reports (if applicable)

Factory Acceptance Test (FAT)

Compliance certificates: CE / GMP / FDA / ATEX

Tank type: Vertical / Horizontal

Application: Water / Chemical / Oil / Pharma / Food-grade

Orientation: Vertical / Horizontal

Installation: Aboveground / Indoor / Outdoor

Total volume

Working volume

Height

Diameter

Wall thickness

Shell/head material: SS304 / SS316 / CS /

Internal lining/coating: Epoxy / Rubber / PTFE / Food-grade

External finish: Painted / Polished / Cladded / Insulated

Design code: ASME / API / IS / ISO

Design pressure

Design temperature

Corrosion allowance

Wind/seismic design

Certification: GMP / FDA / CE / ATEX (if applicable)

Type: Tubular / Flat / Full-length window

Mounting: Welded / Flanged / Clamped

Glass material: Borosilicate / Acrylic / Toughened

Level range: Full or partial

Protection: Guard rods / Cage

Backlight/scale: Optional

Cleanability: Easy-clean / Sanitary design

Inlet nozzle

Outlet nozzle

Drain nozzle

Overflow nozzle

Vent/breather nozzle

Sampling port

Manhole / Handhole

Sight glass ports

Thermowell

Support type: Legs / Skirt / Saddle

Anchor bolts

Earthing lug

Sight glass (main level indicator)

Optional level sensor: Radar / Ultrasonic / Magnetic

Temperature sensor

Pressure gauge (if pressurized)

Level alarms: High / Low

Insulation type: Rock wool / PUF

Thickness

Cladding material: SS / Aluminum / GI

Drain valve type

CIP/SIP system: Yes/No

Spray ball / Rotary cleaner

Sanitary fittings: Tri-clamp / DIN / SMS

Pressure/vacuum relief valve

Emergency vent

Flame arrestor (if required)

Overflow protection

Bund wall (if required)

Sight glass protection

Electrical supply

Compressed air

Steam / Hot water / Chilled water

Gauge lighting (optional)

Material Test Certificates (MTC)

Welding docs: WPS / PQR / Welder certificates

Hydrotest report

NDT reports (if applicable)

Factory Acceptance Test (FAT)

Compliance certificates: CE / GMP / FDA / ATEX