Tecnicon Engineering Private Limited

100 liters to 900 liters

Stainless Steel SS304 / SS316 / SS316L (preferred for hygiene and corrosion resistance)

Optional: HDPE / PP / Glass (for cost-effective or chemical-specific use)

Vertical cylindrical with flat or dished bottom

Optional: Jacketed for heating/cooling

Top-mounted agitator, with:

• Anchor, paddle, propeller, or magnetic stirrer

• Speed: Fixed or variable (using VFD)

• Motor: 0.18 to 1.5 kW, depending on size

Skid-mounted or portable on caster wheels

Optional: Tabletop for lab use

Manhole or lid (hinged or clamp-type)

Charging port for powders/liquids

Vent/filter nozzle

Optional: Light, sight glass, or CIP spray ball

Discharge nozzle with ball valve or flush valve

Optional: Sampling valve

Jacketed with hot water / steam / chilled water

Electric heaters with thermostat for precision heating

ON/OFF switch

Variable speed drive (VFD)

Temperature control (if heated)

Internal: Mirror polished (Ra ≤ 0.4 µm for pharma/cosmetic use)

External: Matte or polished finish

Temperature sensor (RTD/Thermocouple)

Level indicator

Load cell system (for precision batching)

Hydro test

Visual and weld inspection

Electrical safety test (if powered)

Mixing creams, gels, and lotions (cosmetics)

Liquid blending (chemicals, detergents)

Pilot-scale pharma or food product formulation

Laboratory R&D or formulation trials

Vertical cylindrical or horizontal cylindrical

Fixed or skid-mounted

Open top or closed top (with manhole or lid)

Mild Steel (IS 2062 Grade B or equivalent)

Optional: Internal surface with rubber lining, epoxy coating, or FRP lining for chemical resistance

Range: 500 liters to 50,000+ liters (customizable)

Top-mounted or side entry

Types: Paddle, propeller, turbine, or anchor type agitator

Fixed or variable speed (with VFD)

High-speed or slow-speed based on mixing requirements

TEFC or flameproof motor (IP55/IP65)

Gearbox: Inline helical or worm gear reducer

Power: 0.5 HP to 15 HP depending on size and duty

Internal: Painted with chemical-resistant epoxy or rubber lined

External: Red oxide primer + industrial enamel paint / PU paint

Flat, conical, or dished bottom

Sloped bottom for complete drainage

Drain nozzle at lowest point

Inlet / Outlet nozzles (flanged or threaded)

Drain valve (ball or gate valve)

Manhole (top or side, bolted cover)

Air vent or pressure/vacuum relief (if sealed tank)

Temperature sensor port (optional)

Sampling point (optional)

Vertical tanks: Skirt, legs, or ring base

Horizontal tanks: Saddle supports with base plate

Anchor lugs for foundation fixing

External half-pipe coil or internal coil for heating/cooling

Medium: Steam, thermic fluid, or chilled water

Insulation: Rock wool / glass wool with cladding (if required)

Agitator start/stop

Speed control via VFD

Overload and trip protection

Level/temperature indication (if sensors installed)

Lifting lugs for crane handling

Forklift slots (for small portable tanks)

Hydrostatic testing (1.5x design pressure)

Agitator trial run

Weld visual inspection

Coating/lining thickness and adhesion test

IS 803 (Code for Design of Steel Tanks – India)

ASME Section VIII Div. 1 (for pressure tanks)

API 650 (for large field-erected tanks)

Vertical cylindrical or horizontal cylindrical

Fixed or skid-mounted

Open top or closed top (with manhole or lid)

Mild Steel (IS 2062 Grade B or equivalent)

Optional: Internal surface with rubber lining, epoxy coating, or FRP lining for chemical resistance

Range: 500 liters to 50,000+ liters (customizable)

Top-mounted or side entry

Types: Paddle, propeller, turbine, or anchor type agitator

Fixed or variable speed (with VFD)

High-speed or slow-speed based on mixing requirements

TEFC or flameproof motor (IP55/IP65)

Gearbox: Inline helical or worm gear reducer

Power: 0.5 HP to 15 HP depending on size and duty

Internal: Painted with chemical-resistant epoxy or rubber lined

External: Red oxide primer + industrial enamel paint / PU paint

Flat, conical, or dished bottom

Sloped bottom for complete drainage

Drain nozzle at lowest point

Inlet / Outlet nozzles (flanged or threaded)

Drain valve (ball or gate valve)

Manhole (top or side, bolted cover)

Air vent or pressure/vacuum relief (if sealed tank)

Temperature sensor port (optional)

Sampling point (optional)

Vertical tanks: Skirt, legs, or ring base

Horizontal tanks: Saddle supports with base plate

Anchor lugs for foundation fixing

External half-pipe coil or internal coil for heating/cooling

Medium: Steam, thermic fluid, or chilled water

Insulation: Rock wool / glass wool with cladding (if required)

Agitator start/stop

Speed control via VFD

Overload and trip protection

Level/temperature indication (if sensors installed)

Lifting lugs for crane handling

Forklift slots (for small portable tanks)

Hydrostatic testing (1.5x design pressure)

Agitator trial run

Weld visual inspection

Coating/lining thickness and adhesion test

IS 803 (Code for Design of Steel Tanks – India)

ASME Section VIII Div. 1 (for pressure tanks)

API 650 (for large field-erected tanks)

ASME Section VIII Div. 1 (for pressure-rated vessels)

cGMP compliance (for pharmaceutical and biotech applications)

FDA / 3A standards (for food and beverage use)

API 650 / 620 (for large or industrial tanks)

Ranges from 50 liters to 50,000 liters (customizable)

Common sizes: 100 L, 500 L, 1000 L, 2000 L, 5000 L etc.

Stainless Steel: SS304, SS316/316L

Carbon Steel (for non-corrosive applications)

Lined Options: Glass, PTFE, rubber

Conventional Jacket (full shell coverage)

Dimple Jacket (spot-welded, efficient heat transfer)

Half-Pipe Coil Jacket (for high-pressure applications)

Limpet Coil (external helical coil)

Agitator Types: Propeller, Turbine, Anchor, Paddle, High-shear

Drive Types: Top-mounted (standard), side or bottom-mounted

Motor: Electric motor with gearbox, optional VFD

Speed: Fixed or variable (typically 10–300 RPM)

Steam

Hot Water

Thermal Oil

Chilled Water

Glycol-Water Mixture

Jacket Working Pressure: 2 to 10 bar (higher for steam)

Tank Pressure: Atmospheric or vacuum-rated

Design Temperature: –20°C to 200°C

Leg Mounted

Skid Mounted

Platform or Floor Mounted

Insulation: Glass wool or polyurethane with SS cladding

Manhole / Access Ports

Sight Glass

CIP/SIP Ports (Clean/Steam In Place)

Instrumentation: Temperature sensors, pressure gauges, level sensors

Discharge Valve: Bottom outlet (butterfly or ball valve)

Internal Surface: Mirror-polished (Ra ≤ 0.4 µm for sanitary applications)

External Surface: Matte, mirror-polished, or painted

Nominal Capacity: 500 Liters

Working Capacity: ~450–480 Liters (depends on design)

Design Type: Cylindrical vertical tank with dished or flat bottom

Shell & Bottom: Mild Steel (IS 2062 grade or equivalent)

Top Cover: Mild Steel (removable or fixed)

Internal Lining (Optional):

• Epoxy coating

• Rubber lining

• FRP lining

External Finish: Red oxide primer + enamel paint (standard)

Type: Paddle, propeller, or anchor type (based on viscosity)

Motor: Electric motor with gearbox

• Power: 0.5 HP to 2 HP (typical, based on application)

Mounting: Top-mounted (flange or bracket support)

Speed: Fixed or variable (10–300 RPM depending on drive)

Drive Type: Inline or geared motor

Optional: VFD for speed control

Mounting: Leg-mounted (3 or 4 legs with base plate)

Top Cover: Open, bolted, or hinged (based on requirement)

Bottom Type: Flat or dished

Manhole: Optional, based on cleaning requirement

Inlet Nozzle: 1” or 1.5” (customizable)

Outlet Nozzle: 1” to 2” with ball/butterfly valve

Vent / Overflow: 0.5” to 1”

Drain: Bottom outlet with valve (optional flush type)

Instrumentation Ports: For temperature sensor or level gauge (optional)

Diameter: ~800 mm to 900 mm

Height: ~1000 mm to 1200 mm (without motor)

Wall Thickness: 3 mm to 6 mm (depending on design pressure)

Pressure: Atmospheric (standard); pressurized design optional

Temperature: Ambient to 100°C (depends on application and lining)

Level indicator (glass or float type)

Sight glass

Thermowell for temperature probe

CIP spray ball (Clean-In-Place)

Load cells for weight measurement

Internal baffles (for better mixing)

Paint & coating mixing

Chemical blending

Pulp and slurry preparation

Water treatment dosing

Detergent & cleaning chemical preparation